|
#1
17-11-2004, 06:42
|
||||
|
||||
LA Chips and Pin 17
So, just how easy is this thing to get it to lift?
Any tips/foolproof methods to lift the pin from the board? Thanks a lot... LUFCfan 
__________________
[SIZE=3][COLOR=orange][B][COLOR=blue]PS2, [/COLOR][COLOR=yellowgreen]XBOX[/COLOR] & [COLOR=darkolivegreen]Xbox 360[/COLOR] installs / repairs in [U][COLOR=red]West Yorkshire,[/COLOR][COLOR=red] UK[/COLOR][/U] - [COLOR=#ff0000]Nationwide Service [/COLOR][COLOR=darkorange]-[/COLOR]Please Contact me by PM for more info[/B][/COLOR][/SIZE] :) [B][SIZE=4][COLOR=#ff0000][COLOR=seagreen]360 DVD Drive Fw.[/COLOR] [COLOR=orange]Upgraded/Recovered/Restored -[/COLOR] Bad Flash? No Problem! [COLOR=blue]PM for info[/COLOR][/COLOR][/SIZE][/B] [B][SIZE=4][COLOR=#ff0000][COLOR=yellowgreen]XBOX 360[/COLOR] [COLOR=blue]v1.0[/COLOR] [COLOR=blue]- [/COLOR][/COLOR][COLOR=red]Samsung TS-H943A [COLOR=orange]w/ iXtreme 1.4 Fw.[/COLOR] :D [/COLOR][/SIZE][/B] 
|
| Sponsored Links |
|
#2
17-11-2004, 06:58
|
||||
|
||||
|
hey,
its quite easy u need both hands! Get a small screwdriver in your left hand and the soldering iron in ur right. Now touch the iron with the base of the chip let it heat up now gently with the screwdriver tuck it underneath the pin and lift do not apply 2 much preasure otherwise you could snap the chip leg 
__________________
[COLOR=Black][B]if it isnt broke dont fix it![/B] [B]www.consoleupgrades.co.uk For All your console needs[/B] [COLOR=RoyalBlue][B]UK'S No.1 I.C.E [URL=www.audiorebel.co.uk]www.audiorebel.co.uk[/URL][/B][/COLOR] [/COLOR][COLOR=DarkSlateBlue][/COLOR] [COLOR=Black][B][/B][/COLOR][COLOR=DarkSlateBlue][/COLOR]
|
|
#3
18-11-2004, 05:03
|
||||
|
||||
lifting legs
 put two small razor blades eather side and heat up the leg with the soldering iron and apply Pressure to the blades at the same time the leg should lift up don't lift the leg too high or it will snap and then the fun starts
__________________
1800 AMD 1027 ddr Pioneer DVR-A07 the university of limerick chipper ps2 v10 pal+ripper2 gold (new baby) ps2 v6 pal+duo chipped by me Don’t take life too serious you’ll never get out alive!
|
|
#4
18-11-2004, 10:00
|
||||
|
||||
|
I used an exacto knife. Put the blade under the leg and heat the leg with the soldering iron. While its placed gently push the leg up with the exacto. Don't leave the soldering iron on too long or you can burn the board.
Good luck.
__________________
JPunisher
|
|
#5
25-11-2004, 13:37
|
|||
|
|||
|
I use a steel pick with the tip bent to a tiny hook shape, put the pick under the Pin and heat it up with the iron and LIFT.
__________________
Ps2 / Xbox chips installed in Ireland http://www.modchipsireland.com
|
|
#6
25-11-2004, 15:01
|
|||
|
|||
|
.... i didnt even use heat. i just used a metal wire bent into a hook, shoved it under it lifted with all my care. it came off with no force at all. mine was version 9
__________________
[B]v9 [COLOR=Blue]Matrix Infinity[/COLOR][/B]
|
|
#7
25-11-2004, 22:38
|
||||
|
||||
|
Well this is an old post of mine but I explained here how to do it and it works very well. http://www.fileforums.com/showthread.php?t=62487
__________________
[color=blue][size=2][b]Click[url=http://www.ps2-scene.org/forums/showthread.php?t=25770] here [/url]to view refes. Click[url=http://www.norcalmods.com/gallery] here [/url]to view install gallery[/b][/size][/color] [size=2][b][color=red]Mod chip installs and repair [/color][/b][/size] [url]www.norcalmods.com[/url]
|
 |
|
|
Linear Mode
